AVR Programmer

[wellnerson1]

Here you can find a lot of Programmers for AVR, PIC etc..

http://www.lancos.com/

[ph_cabral]

In the very feel of Atmel, you might find the recorders of AVR,
The AVR Dragon, low-cost and well attraction

www.atmel.com

or

www.at91.com

[an007]

http://www.embedded-projects.net/index.php?page_id=165

[genviktr]

And it is the reference on usb programmer for Atmel AVR controllers.
 http://www.fischl.de/usbasp/

[30f4011]

Hi , This may help you:
http://www.ikalogic.com/isp.php

[kevin8]

USBasp - USB programmer for Atmel AVR controllers
very cool USB programmer,you can visit http://www.fischl.de/usbasp/    for more info

[pak]

Check this site too. It is a parallel port programmer for both the 8051 and AVR series devices.

http://chaokhun.kmitl.ac.th/~kswichit/SPI_Pgm/SPI-Pgm37.html

And Pony2000 programmer from

http://www.lancos.com/prog.html

And the hardware schematic is

http://www.lancos.com/e2p/betterSTK200.gif

I use both programmers.
pak


Happy Microcontroller Programming 


Posted on: July 17, 2008, 04:26:39 16:26 - Automerged
Another AVR programmer is avrdude. avrdude is come with winavr, a free compiler
http://winavr.sourceforge.net/download.html

avrdude can be used as command line and gui as well. For gui, go to C:\WinAVR-20080512\bin and run avrdude-gui.exe. before you use it, you have to install "install_giveio.bat"

Note: I'm not use avrdude very often.

pak

[94491203]

who have this avr mkii sch

[eleckits]

And it is the reference on usb programmer for Atmel AVR controllers.
 http://www.fischl.de/usbasp/

I have some questions relating usb programmer for Atmel AVR controllers that you mentioned above :

What's the configuration bits for ATMEGA8?

I hope to reply as soon as possible.

[anatom]

I have some questions relating usb programmer for Atmel AVR controllers that you mentioned above :

What's the configuration bits for ATMEGA8?

I hope to reply as soon as possible.

try this...
http://palmavr.sourceforge.net/cgi-bin/fc.cgi

[wellnerson1]

Hi Everyone,
I have built a HV AVR Programmer with reference to the following web site:
http://www.der-hammer.info/hvprog/index_en.htm
Some times it works fine and in some other time it says that it cannot contact the programmer . And even in some times the signature or fuse bits or lock bits it read out are incorrect . i have done every thing in parallel HV mode. But the same chip is working fine with avr 910 programmer . Can any body tell me any suggestion or any tuning is required?

Thanks in advance

[DarkClover]

Is it the same problem if you try on another computer ?
My problem was another driver which interrupted the programmer.

[wellnerson1]

Hey Friends i found out the problem!!. Its due to the power supply. The HVProg works fine in ISP mode fantastically, dont have any absolute stiff power criteria, but in Parallel mode HVProg the power supply should be stiff to 12V and 5V otherwise lots of ambiguous responses came from the SW.
Thanks for your reply dear DarkClover.

[wellnerson1]

Dear Friends,
Khazama AVR Programmer v1.7 a new version is released which can support new USBASP firmware version :  2011-05-289 TPI support (supports programmers with ATMega88 and ATMega8).
Link is: http://www.khazama.com/project/programmer/

Comment on Khazama: Works nicely as what it is intended for!!